20Luberfiner LW4076XL Design Change Tech Tip

TECH Tips CATALOG NUMBER 20 www.midwestwheel.com NLINE www.midwestwheel.com Order NLINE ™ MIDWESTWHEEL.COM IOWA MISSOURI DES MOINES 1436 E. Ovid Ave. office 515.265.1491 fax 515.265.4120 parts fax 800.314.4329 parts 800.888.0248 CEDAR RAPIDS 200 50th Ave. S.W. main 319.365.4453 fax 319.365.6327 parts fax 877.706.6085 parts 800.332.5435 DAVENPORT 8502 Northwest Blvd. main 563.322.2671 fax 563.322.5940 parts 800.553.1886 SIOUX CITY 1819 4th St. main 712.252.7969 fax 712.252.6149 parts 800.943.3534 CLEAR LAKE 840 Hwy. 18 W. main 641.357.7101 fax 641.357.8190 parts fax 800.548.9674 parts 800.397.5630 TRUCK PARTS SUPER STORE TM KANSAS CITY 5801 E. Front St. main 816.471.1552 fax 816.471.0813 parts 800.821.7402 JOPLIN 2424 Stephens Blvd. main 417.717.6022 fax 417.782.7126 parts 866.318.9111 LF LW4076XL Design Change 200 South 4th Street Albion, IL 62806 Hotline: 800-882-0890 www.luber-finer.com © 2020, Champion Laboratories, Inc. An ISO14001 and ISO/TS16949 registered company. 200 S. 4th Street Albion, IL 62806-1313 SERVICE BULLETIN Date: March 20, 2020 To: Luber-finer® Customers From: Luber-finer® Subject: LW4076XL Design Change Service Bulletin: March 20, 2020 LW4076XL Design Change Luber-Finer has made a design change to the LW4076XL. This change does not affect filter performance. The largest difference is that the OE filter snaps into the OE housing cap, whereas the new Luber-finer filter does not. Both filters have the same sealing surface on the bottom of the filter. As shown in the picture above, both the OE and Luber-finer filter have the same dimensions and seal into the housing the same way. For installation of the LW4076XL, follow these directions: 1. Lubricate all housing or filter o-rings. 2. Install the Luber-finer filter into the housing. 3. Install the OE housing cap as normal. Note: If the OE housing cap is difficult to tighten, make sure the filter is seated all the way down inside the housing. For removal of the LW4076XL, follow these directions: 1. Unscrew the housing cap (filter will still be in housing). 2. Insert finger in filter hole or grasp the top of the end cap to pull filter out (this will allow you to reduce the amount of spilled coolant). Note: The Luber-finer filter does not snap into the housing cap and will not come out with the housing cap. To recap, the Luber-finer LW4076XL design does not alter the filter’s performance. The only changes concern the filter’s appearance and the procedures in which you will need to install and remove the filter. (OE filter on the left / Luber-finer filter on the right) (OE Filter on the left / Luber-finer filter on the right) (Installation and removal of the Luber-finer LW4076XL) 200 South 4th Street Albion, IL 62806 Hotline: 800-882-0890 www.luber-finer.com © 2020, Champion Laboratories, Inc. An ISO14001 and ISO/TS16949 registered company. 200 S. 4th Street Albion, IL 628 6-1313 SERVICE BULLETIN Date: March 20, 2020 To: Luber-finer® Cu stomers From: Luber-finer® Subject: LW4076XL Design Change Service Bulletin: March 20, 2020 LW4076XL Design Change Luber-Finer has made a design change to the LW40 76XL. This change does not affect filter performance. The largest difference is that the OE filter snaps into the OE housing cap, whereas the new Luber-finer filter does not. Both filters have the same sealing surface on the bottom of the filter. As shown in the picture above, both the OE and Luber-finer filter have the same dimensions and seal into the housing the same way. For installation of the LW4076XL, follow these directions: 1. Lubricate all housing or filter o-rings. 2. Install the Luber-finer filter into the housing. 3. Install the OE housing cap as normal. Note: If the OE housing cap is difficult to tighten, make sure the filter is seated all the way down inside the housing. For removal of the LW4076XL, follow these directions: 1. Unscrew the housing cap (filter will still be in housing). 2. Insert finger in filter hole or grasp the top of the end cap to pull filter out (this will allow you to reduce the amount of spilled coolant). Note: The Luber-finer filter does not snap into the housing cap and will not come out with the housing cap. To recap, the Luber-finer LW4076XL design does not alter the filter’s performance. The only changes concern the filter’s appearance and th procedures in which you will ne d to install and remove the filt r. (OE filter on the left / Luber-finer filter on the right) (OE Filter on the left / Luber-finer filter on the right) (Installation and removal of the Luber-finer LW4076XL) Luber-Finer has made a design change to the LF LW4076XL. This change does not affe t filter performance. The largest diff rence is hat the OE filt r snaps into the OE housing cap, whereas the new Luber-finer filter does not. For installation of th LF LW4076XL, follow the directions: 1. Lubricate all housing or filter o-rings. 2. Install the Luber-finer filter into the housing. 3. Install the OE housing cap as normal. Note: If the OE housing cap is difficult to tighten, make sure the filter is seated all the way down inside the ho sing. For removal of the LF LW4076XL, follow these directions: 1. Unscrew the housing cap (filter will still b in housing). 2. Insert finger in filter ole or gr sp the top of th end cap to pull filter out (this will allow you to reduce the amount of spilled coolant). Note: The Luber-finer filter does not snap int the housing cap and will not come out with the housing cap. To recap, the Luber-finer LF LW4076XL design does not alter the filter’s performance. The only changes concern the filter’s appearance and the procedures in which you will need to install and remove the filter. Both filters have the same sealing surface on the bottom of the filter. As shown in the picture above, both the OE and Luber-finer filter have the same dimensions and seal into the housing the same way. (Installation and removal of the Luber-finer LF LW4076XL) (OE filter on the left / Luber-finer filter on the right) (OE Filter on the left / Luber-finer filter on the right) March 23, 2020 (20Luberfiner LW4076XL Design Change Tech Tip)